Happy Holidays and Wishing Everyone a Great New Year!
Monday, December 24, 2018
Thursday, December 20, 2018
Morikawa SE2A3 in Jose's Listening Room
Back in the 90s I used to hang out with Ding and Jose at Hamfests in the suburbs of Philly. Jose isn't your typical audio nerd who subscribes to the latest is best mentality. He goes for value for money and although not a DIYer, has an eye and ear for quality design! Even if he has a Technics SP10 + Sumiko MMT turntable combo, most of his listening nowadays is through a high quality pre-bitstream a Denon DCD 1500 and a stable platter Pioneer PD65.
Having heard that a well designed SE2A3 amp is a synergistic match for his Altec 604-8Gs, he spotted and won this Chuyu Morikawa designed Audio Professor SE2A3 amp on eBay. However, the amp had two issues. The input level controls were no longer functioning, and worse, the amp was unstable manifested by extra-musical popping and whistling sounds. Since we're practically neighbors now, I took it home for a check-up.
Having heard that a well designed SE2A3 amp is a synergistic match for his Altec 604-8Gs, he spotted and won this Chuyu Morikawa designed Audio Professor SE2A3 amp on eBay. However, the amp had two issues. The input level controls were no longer functioning, and worse, the amp was unstable manifested by extra-musical popping and whistling sounds. Since we're practically neighbors now, I took it home for a check-up.
Under the hood
Beautiful workmanship, typical of a handcrafted amplifier from Japan
After installing a dual ganged 100k Alps audio taper input pot, I realized that the cause of instability was the step down transformer the eBay seller sold with the amp. It was hardly stepping AC down to 100V. During the amp's residency here at JE Labs it was plugged to a General Radio Variac set to 100VAC. It was stable and quiet. Fortunately Jose also has a Variac on stand by, which he acquired during our Hamfest hunting days.
6Z-DH3A
The amp uses 4 x (2 for each channel) 6Z-DH3A, UX-6 based, high-mu triodes as input/driver tubes. This tube is electrically equivalent to an octal based 6SQ7. AFAIK, there are no plug-in compatible US or European equivalents.
The input/driver circuitry is configured in SRPP, very similar to what I did in the JE Labs SRPP 45/2A3, albeit with textbook operating points.
Luxman SS5B-2.5k OPT
 |
| 100Hz |
 |
| 1kHz |
 |
| 10kHz |
These square waves show that the Luxman SS5B 2.5K primary SE OPTs are of very high quality. Not much information is available on the internet regarding this transformer aside from completed auctions, but I've encountered this model in schematics and pictures in Asano's two volume tome on tube amplifiers.
Since Luxman SE OPTs were no longer available during the Sound Practices era in the 90s, I would date this amplifier to the 80s, at the latest. That's before Cary introduced the 6SL7 SRPP driven 300B or 2A3 AES SE-1 kit amp to the mainstream market.
I built SRPP circuits back in the day, but was never a fan of this topology. However, this amp made me reconsider my stance. Now I'm asking myself - could it be the textbook operating points and/or the 6Z-DH3A input/driver tubes which made this experience memorable?
I truly enjoyed listening to this amp, thanks Jose!
Friday, December 14, 2018
Susumu Sakuma
Susumu Sakuma, RIP
(1943-2018)
Photo courtesy of my Flickr friend silver_night 300b
Sakuma-san and Brian "monofantastico" Clark were my mono hi-fi system heroes!
Tuesday, December 4, 2018
Denon Aluminum Body Cap
I've been a Denon DL103 user for more than two decades but never considered risking my $250 investment to modifications which involved removing the old and installing another body.
To circumvent the risk of damaging the stylus/cantilever assembly, Steve Bedard came up with the Denon Aluminum Body Cap.
The finely machined aluminum cap slips over the Denon DL103 body. I noticed a slightly tighter fit on the DL103R and DL103C1, due to the different housing material used for these higher end models.
Two longer metric bolts are supplied to fit the original Denon nuts to compensate for the added thickness when mounting the cartridge/cap combo to a head shell.
It has been my experience in this hobby that every time the frequency extremes are improved, something gives and usually, it is the midrange that suffers.
The classic DL103 is a case in point. It has a wonderful midrange but it has a tendency to congest in the high frequencies during complex musical passages. Brighter recordings can also sound sibilant while the lower frequencies can gain more definition.
Through the years, Denon has addressed these issues with "upgraded" DL103 versions by revising the coil with finer quality wire and by using more inert materials for the housing. I have two of them - the current DL103R and its predecessor, the DL103C1. Both models refine the frequency extremes but at the expense of a drier and "less colorful" midrange.
Thankfully the "capped DL103" retains and focuses that midrange warmth, almost mimicking an SPU, while the frequency extremes are tidied up. There's just a hint of sibilance and congestion left with the "capped DL103."
Even if there was improvement across the audio band with the aluminum cap installed on either DL103R or DL103C, what was most apparent was better definition in the lower frequencies.
Could it be that the upgraded DL103 models benefit less from the cap? Perhaps the distinction might be system dependent and/or merely a matter of taste? Just remember, I'm not a mainstream audiophile. 😉
What I like most about the Denon Aluminum Body Cap is, it doesn't dampen the virtues of the DL103/103R/103C1. It highlights and improves upon what's already there.
In the big scheme of things, it's hard to find this level of sonic upgrade for under $100. My DL103 is "capped" for good, highly recommended! 👍
Wednesday, November 21, 2018
November 2018 Hi-Fi Show Pics +
G.I.P. Laboratory
Room 646
 |
| GIP 225 |
 |
| Ben, Lin and Ayie |
 |
| Francis, Ben and Mickey |
 |
| Ben, Joey (Harana Audio), Allan (DEQX) and Suzuki-san (G.I.P Labs) |
G.I.P. Laboratory + Harana Audio
Room 647
A Visit to G.I.P. Labs
Saturday, November 3, 2018
'70s Direct Drive Turntables (and Tonearms)
This is a follow up on the road less travelled article. In 2017, I went on a quest for direct drive turntables that I could acquire for under $250. For the past year I've been tinkering and listening to these four 70s era direct drive turntables to find out whether a direct drive turntable has a place in my ever-growing collection of audio equipment.
Each unit has its own unique approach to direct drive turntable design and was available either as an integrated unit (with tonearm) or as a plain motor unit. The Denon DP1250, Kenwood KD500 and JVC QL5 are mid-priced models from the late 70s, while the Sony TTS2500 was a first generation early 70s top of the line direct drive unit designed to compete with the original Technics SP10, which, unfortunately, was not within my budget. 😞
Each unit has its own unique approach to direct drive turntable design and was available either as an integrated unit (with tonearm) or as a plain motor unit. The Denon DP1250, Kenwood KD500 and JVC QL5 are mid-priced models from the late 70s, while the Sony TTS2500 was a first generation early 70s top of the line direct drive unit designed to compete with the original Technics SP10, which, unfortunately, was not within my budget. 😞
Turntables
 |
| JVC QL5 |
JVC introduced the world's first quartz locked turntable in 1974. The QL5 employs quartz locked circuitry to control its 12 pole 24 slot DC type motor. Its jet black plinth is made out of heavy particle board. The motor unit was also sold sans tonearm as the QL50.
 |
| Kenwood KD500 |
Instead of the complex electronics found in the Denon, JVC and Sony, the KD500 uses a relatively simple servo circuit referenced to a frequency generator modulating an 8 pole 24 slot brushless DC motor. This turntable developed a following in the late 70s due to the use of a highly inert and heavy synthetic marble plinth.
This particular unit was loaned to me by my buddy Ding. He's had it stored for many years. It ran way too fast at first turn on so I replaced these four bulging capacitors immediately.
 |
| Denon DP1250 |
Unlike the two preceding turntables, the DP1250 uses an AC motor which minimizes cogging, according to period Denon sales literature. The motor is governed by a unique tape head inspired speed regulating system. The plinth is a substantial plywood/particle board laminate similar in mass to the JVC.
 |
| Sony TTS2500 |
The Sony TTS2500 is the motor unit of the worldwide bound Sony PS-2250/2251. Just like the Denon, it also uses an AC motor regulated by a servo circuit that is claimed to be practically cog-less in operation. This JDM (Japanese Domestic Market) model requires a 100V step down transformer. The half-finished laminated plywood plinth was DIY'ed by yours truly.😎
Tonearms
In a typical audiophile shootout these turntables would have been fitted with the same tonearm/cartridge combination and plinth. But this was not practical since I wanted to test under real world conditions. So to satisfy JE Labs' retro-centric streak,😉 for the Denon and Sony, I chose period correct gimbal bearing type tonearms that are known to perform on a similar musical level as those supplied with the QL5 and KD550.
 |
| JVC QL5 Tonearm |
The QL5 is equipped with a tonearm that looks like an economy version of their well regarded UA-5045. With an effective length of 245mm, it is a bit longer than the three 237mm tonearms below.
 |
| Kenwood KD550 Tonearm |
Ding had a Grace 707 installed before moth-balling this KD500. For some reason that tonearm went AWOL. Fortunately I had the original tonearm supplied with the KD550 in my stash. There are claims that this may have been OEM'd either by Acos or Micro-Seiki?
 |
| Rega R200 |
It would've been nice if I had something along the lines of a Denon DA305 to fit on the DP1250. However, the Acos OEM'd Rega R200 I installed is also a well respected 70s classic.
 |
| Grace 540L |
I've always had a soft spot for Grace/Shinagawa tonearms ever since the Grace 707 opened my ears that fine quality tonearm design produces nice sounds. This Grace G540L has similar mass to the other three above. The lack of a cuing device and anti-skate betrays its pro-application heritage. It is the oldest of the bunch making it the perfect partner for the TTS2500.
Cartridge
 |
| Denon DL103R |
For critical listening I relied on a Denon DL103R mounted on a Sumiko HS-12 head-shell. But this didn't prevent me from mounting a variety of cartridges in my stash ranging from the cheap 'n cheerful AT 3600L to an Ortofon SPU.
Time travel to the 70s
Without hesitation, I would choose any of these turntables over the 3-point suspension belt drive turntable I used and tweaked to the max in the 80s. The direct drive system has the sure-footed speed stability which eventually lured me to the TD124 in the late 80s. I should've jumped at bargain priced top of the line direct drives to play with in the 90s...alas, hindsight is 20/20.
Since direct drive solved the ills of wow and flutter, and noise which plagued the belt and idler drive system respectively, there should be minimal difference in the way any direct drive motor unit should sound, right? Not quite...
 |
| Denon AC motor (top) Kenwood DC motor (bottom) |
My most surprising discovery after living with all these turntables this past year was the difference in sound between the motors that power them. The DC-motor-powered JVC and Kenwood consistently sounded analytical, cold and forward, akin to a digital source, while the AC-propelled Denon and Sony were characteristically more laid back and warm, just like what I associate with analog sound.
However, to put things in perspective, the Sony still outperformed the other three direct drives in key musical aspects. In particular, there is a "hardness" and loss of composure in complex musical passages that prevailed on the three units with the Sony exhibiting only the very least amount.
 |
| Sony TTS2500 + Stax UA-3NL |
Still, the TTS2500 could not eclipse the performance of the 301 or the TD124s. But it is the only direct drive in this group to come close in mimicking the stately authority of the esteemed idler driven classics.
For this achievement, I crowned the Sony with a 12" Stax UA-3NL tonearm.🍻