Electro-Voice EV 209-8A - 8" wide-range

During a visit to Sakuma's Direct Heating website, I encountered a cool SE 801 amp schematic designed for either a Lowther PM6 or an Electro-Voice 209-8A. I googled the EV 209-8A and nothing came up in Audio/DIY centric English language websites. But there were a lot of US dealers stocking the driver from as low as $18 each.

basic specs

After downloading and studying the detailed specifications at the EV website, I chose the cheapest internet seller and phoned-in an order for a pair. 

It cost $40/pair from Full Compass delivered within a couple of days to my doorstep. In spite of their great customer service, their packing left a lot to be desired - see the slightly wrinkled whizzer in the above right picture - the drivers were free floating in the box, not even tied down face to face ;( 

Due to lack of resources to build the recommended 1.8 cubic foot sealed cabinet, I loaded the EV 209-8A in a Heathkit 1.2 cubic foot ported cabinet, which used to house a Jensen P8RL + RP103. 

Heathkit 1.2cf + EV209-8A

Sharp fall off below ~ 90hz, otherwise the in-room RTA result was satisfactory. The tonal balance reminded me of a good mini-monitor speaker with no upper midrange nasties. It was also quite extended in the high frequency and at no time did I crave for a super tweeter.

Further internet research yielded this Japanese website which did an in-depth study of the EV 209-8A. Based on Chrome browser translation, transmission line loading was used to get around the bass deficiency.

Regardless of Qts values ;) and in keeping with JE Labs tradition, a trial in an open baffle is de rigueur. Since my original pair of OBs are currently in storage, I improvised a 55" wide x 32" high flat baffle using a 24" x 24" x 1/2' thick pine plywood baffle from my experiments in the 90s as the core, supplemented by cardboard extension wings.

OB + EV209-8A

Despite the even sharper fall off in mid bass response as shown in the RTA, subjectively, the bass extension was similar to the EV209-8a/Heathkit box combo. But the scale of the sound field produced by the EV209-8A/OB combo was a lot larger than when it was loaded in the Heathkit cabinet.

Since I discovered that my very first high efficiency speaker (a green KS 14703/Altec 755C) was carefully stashed in a box in the basement, I installed it in the OB to take a trip down memory lane. 

OB + Altec 755C

I've covered the Altec 755C in the Sound Practices No. 17 Homebrewer feature many moons ago, so I will spare adjectives to describe the subjective performance of the KS14703/755C. Suffice to say that the above RTA graph shows it all. It is just in a different class sonically and affordability! Perhaps not a very fair comparison for the EV209-8A because this driver with an intact cone and voice coil is worth about 20 times more when they come up for sale.

So even if I couldn't coax Altec 755C performance from the EV209-8A, its street price, efficiency, relatively flat impedance curve and midrange to upper frequency performance quality impressed me enough to bring it to the attention of the Audio/DIY world. 

Noguchi Finemet

Just a preview ;)

je2a3 amp

Twenty three years ago, I built my first 2A3 amp in the basement of the very same house I'm staying in right now. This was a pair of PP2A3 amps with a Mullard-Style driver circuit pumping 8W per channel of pure Class A to drive 82dB/1W/1M (in)efficient BBC LS3/5As, with external preamplification.

As I enter another phase in life, I am back in the same house, mellower with age but hopefully wiser, building a single channel, single-ended 2A3 amp with 3.5W output to drive a 99dB/1M/1W efficient Altec 2-way horn system, with a phono and line stage on board.

This project started with a chassis and choke (amongst other things) handed over by Joe Roberts at the Capital Audio Fest last July. Additional parts were either donated by my hamfest/radio show buddy, Chong Ong or ordered online, like the Hammond 272X power transformer, which came from Steve at Angela Instruments. Back in the 90s, I could have built this amp (except for the output transformer) using parts sourced from hamfests and radio shows. But times have changed, sadly for this project, the only parts I got from a hamfest were the tube sockets ;(

I had been exchanging emails with J-Rob regarding the WE/Altec 32, Emilar horns/drivers, ROK idler TTs, viscous damped tonearms, vintage cartridges like GE RPX, Shure M3D, etc. Among the tubes he suggested I try in lieu of my favorite octal 6SL/SN7s and 5-pin 27/37 and 56/76s, which are getting quite expensive, are the Loktal equivalents + the "Mickey Mouse" plate and grid-capped 2C22/7193 med-mu triode.

WARNING: the 2C22 is not for the faint-hearted, there is over 200VDC in the plate cap if accidentally disconnected while the amp is operating!!!

As depicted in the above block diagram, this is classic (nothing new = boring) JE Labs ;) I used 2 x 7B6 loktals in the RCA derived RIAA phono stage sans variable EQ. A stereo > mono mixer via a WE111C repeat coil to process digital sources was integrated into the chassis, then a single medium-mu triode 2C22/7193 acts as a line stage preamp cap coupled to a Radiotron SE2A3 amp.

!!!WARNING!!! 

The voltages found in this circuit can be lethal, build at your own risk!!!

The chassis was painted in Silver Hammerite, but wiring had to wait due to actual music making and more important projects ;)

Fancy-schmanzy boutique parts were not used in this amp - just plain old carbon resistors, paper in oil caps and electrolytics in the tube rectified/choke filtered power supply.

The amp section is currently fitted with a Noguchi PMF-15WS OPT I got in Akihabara. It sounds really good! You just have to take my word for it since I don't have a scope and audio generator to prove it ;)

At a later date I might swap in the PMF-10Ws, but ultimately I'd like to permanently install an American made OPT, maybe an Edcor or ask/beg Mike L. at Magnequest to wind a single TFA204 OPT just to keep the amp an ALL American classic ;)

Time Out

ala  Turk

(Re)building a Hi-Fi Room

ca. 2006

Eight years ago I vacated this space, not knowing that I would be back someday...

Late Spring 2016

Altec 861 cabinet

Among those that didn't make it into the 20 foot container in 2008 was a pair of Altec 861 cabinets loaded with generic 15" drivers. I used one temporarily to get some sounds going in the room while I figured out how to repurpose the other cabinet.

Amplification

Grommes LJ2

 This sweet "Little Jewel" PP6V6 integrated mono amp fired up with no problems after almost 8 years of silence.

Rek O Kut B12GH + Velvet Touch

My hand-carried Velvet Touch tonearm "blu-tacked" on a ROK B12GH and mounted on a state-of-the-art crate plinth. 

After a thorough cleaning and re-lubrication of the main bearing, Papst motor and replacement of motor mounts, the dreaded motor vibration is still felt on the tonearm finger lift. I have to send the idler wheel to Terry Witt for a rebuild and plan on building a heavy plinth.

Unlike the fussy Rek O Kut, this Pioneer PL6U is running quietly on its original lightweight plinth after I replaced the 3 perished rubber motor mounts with rubber grommets + light cleaning and re-lubrication. It sounds great with a $40 Stanton 500 cartridge!  

Pioneer PL6U

Line-level sources

KLH Model Twenty One

Classic Hi-Fi FM table radio found in a bicycle shop. 

Western Electric 111C
+
UTC A20

Stereo > Mono transformer mixer for the iPod Nano

Hi Eff Speaker

Since the Altec 861 (aka Madrid) share a similar internal volume with the Altec 614, I went to Lowe's to get 3/4" plywood cut to the size of the front panel. Using a Harbor Freight Router + Jasper Jig 200, I cut a hole for a rear mounted Altec 414A and a rectangular 2" x 7" port to mimic an Altec 614.

Altec 2-way

Altec 861 loaded with an Altec 414A running full range augmented on top by an Emilar EH800 horn or Altec 32A horn with an Emilar EA175-16 compression driver.

Work in progress...

Altec 605B experiments

Hot on the trail from the 1" compression driver survey, I set forth to re-evaluate my open baffle mounted Altec 605B. This Duplex system is essentially an Altec 416A woofer + Altec 806A compression driver with an integral short horn. I wanted to address a mild honk and try to squeeze out more "air" in the top end from the horn/driver combo.

605B as a 416A woofer

Since my modus operandi has always been to listen carefully to each component as a separate entity, I disconnected the compression driver from the N1600C crossover and listened to the woofer rolling off at about 1100 hz as well as bypassing the crossover, in full range mode. 

After several days of listening with and without the crossover, I realized that the "honk" actually emanated from the woofer. Perhaps this was due to the typical midrange impedance rise in a woofer exacerbated in an open baffle by the lack of a true enclosure? So I winged and auditioned a few Zobel EQ values and ended up with 10 ohms + 11uf in parallel with the woofer terminals as the "best compromise." This circuit cost a couple of dB in efficiency but did not significantly affect dynamics while minimizing the honk. 

Towel damping

Not scientific, but hanging a towel behind the driver focused the sound a bit further ;)

+ Altec 32C horn

For kicks, I did another round of listening with the 605B acting as a woofer coupled to the Altec 32C horn using the same drivers (except the Beyma) and crossover options discussed in the previous survey. But unlike the 12" Altec 414A which has a smooth roll off characteristic, the 605B woofer had to be configured as outlined above. In this configuration, the woofer blended nicely with all four drivers. In fact the 605B woofer section + 32C/802D horn combo had a similar midrange tonal balance to the Altec 2-way. Could that be a 32C horn coloration? ;)

Altec 16 ohm diaphragms

The Altec 605B was factory fitted with the aluminum voice coil 20275 diaphragm. By the time I acquired it, the diaphragm has been replaced with the newer 34852 with a copper voice coil. I've swapped the 34852 and the 20275 (from my 802D) in and out of the 605B and always preferred the midrange oriented 20275 over the more extended high frequencies from the 34852. Thus, to my ears the 34852 and 20275 cannot be used as a stereo pair. Alas, NOS 20275s are very scarce but fortunately GPA is reproducing original 34852 diaphragms. Just to make sure my 34852 is an original Altec item I posted a query at the Altec Users' Board.

34852 vs. 20275

Having confirmed that my 34852 was genuine, I compared the JEL/N1600C XO to the stock N1600C in search of more sparkle and air from the 806A. The JEL/N1600C with EQ circuit did augment the top end a bit, but not to the same degree achieved by the other drivers with more powerful magnets used in the 32B horn experiment above. With or without the Zobel network, I found too much depression in the midrange of the 605B. This was most notable in the vocal range but not as audible with instrumental music. Switching to the 20275 diaphragm improved the midrange a smidgen but I was still not fully convinced that using the JEL/N1600C XO was the proper course.

Coda

Altec N1600C + Zobel EQ

For now I'll continue using the Altec 605B with the N1600C crossover with Zobel EQ + a sparkler...

Sparkler = Altec 3000H

Stereo > Mono Line Level Mixer - ***Revised 4/12/21***

Mixing line level stereophonic signals into full dimensional monophonic ;)

Here's a DIY project for mono aficionados that's so basic, I should have uploaded it many years ago. But other things got in the way.

Just like an MC step-up, these are entirely passive devices. 

The simplest way to convert stereo to mono is to connect left and right channels via a Y connector. But there's a more elegant way than just shorting two channels.

Resistors can blend two signals into one better by...

...using Allen-Bradley carbon composition for warmer sound ;)

Line Output Transformers

This single UTC A-20 transformer was in a box lot of tubes and parts I picked up at a radio show. It's a high quality transformer designed for mic, mixer or line matching applications. Instead of trying to find a mate for MC step-up duty, I repurposed it for a greater calling in my mono rig.

With a claimed bandwidth of 10-50,000 hz and dual windings in the primary and secondary, it is perfect for mixing line level stereo signals into mono!

Left and right channels from a stereo source are fed into each primary winding. The summed mono output is taken from the series-connected secondary winding, which goes into the line level input of a mono preamp.

April 12, 2021 update!

The Covid 19 lockdown was a good opportunity to reassess past projects.

I realized that my original practice of connecting the left and right stereo channels to the split primaries of a single UTC A20 line transformer was sonically inferior to the 2 x Tamura line transformers with their secondaries connected in series as shown above. 

The classic UTC A20 and A21 are still very fine contenders but two are needed instead of one. Use the specs above as a guide for hunting transformers under the radar. 

If you prefer modern transformers, I highly recommend contacting dave slagle of Intact Audio. He winds fine sounding transformers to spec using high quality materials.

He generously provided the following technical explanation as to why my original recommendation was flawed.

• if the L & R outputs share the same core they are effectively in parallel even if the secondaries are connected in series
• if the L & R are on discrete cores and the secondaries are in parallel the circuit can be drawn as one channel driving the other through two transformers
• if the L & R are on discrete cores and the secondaries in series then the load is also part of the series circuit so a high impedance is reflected back

Subjectively, using a single transformer I heard truncated frequency extremes, compressed dynamics and less detail. With two transformers the sound was cleaner and more articulate with more extension at frequency extremes. Dynamic nuances at micro and macro levels improved significantly. There's also a greater sense of space and ambience!

1" compression drivers - Emilar, Renkus-Heinz and Beyma

Is there life after Altec?

My first encounter with Emilar and Renkus-Heinz was in a discussion at the Lansing Heritage forum in 2006. Apparently, Jonas Renkus was a principal at both companies in the 70s and 80s. Prior to co-founding these companies, he worked under John Hilliard at Altec Lansing and followed him at Ling Temco Vought (LTV) where they developed a new compression driver with a polyimide suspension aluminum diaphragm. A paper on this research was submitted to the Journal of the Audio Engineering Society in 1966. This association piqued my interest, which triggered my search for affordable Emilar and Renkus-Heinz drivers.

Soon after I arrived in Manila, I became friends with artisanal speaker craftsman Lin Gomez. He is the go to person for Altec, JBL, Jensen, Western Electric or any vintage driver that needs restoration. His company used to be the official Beyma importer. During his closeout sale of Beyma inventory, among those I purchased was a pair of Beyma CP380M.

For the past couple of years, I've been playing with these drivers in the attic mounted either on the Altec 811, RCF H3709 and Altec 32C. But all of my recent critical listening was done through the mono rig driving one side of the Altec 2-way using the following crossover set up.

Crossover

3khz @ 6dB/octave high pass + HF ATT/EQ
for 16 ohm drivers

To keep things simple, critical listening tests were done with the Altec 414A full range and the above crossover was used for the Altec 802D and Beyma CP380M (both 16 ohms) cutting in @ ~ 3000 hz with a 6dB/octave slope.

3khz @ 6dB/octave high-pass + HF ATT/EQ
for 8 ohm drivers

For the 8 ohm compression drivers the above crossover was used and the 414A running full range. The 8 ohm L-pad substituted in place of a 25 or 30 ohm wire wound pot works just as well.

Splitting hairs

For all intents and purposes, these drivers were designed for similar real world applications. Since each manufacturer had their own set of measurement parameters, I deemed the inclusion of driver specifications inconsequential. Anyway, I noted that the minor differences in driver efficiency were well within the shelving range of the attenuator on both crossovers.

My main objective was simply to find out how each compression driver attached to the Altec 32C horn blends with the outstanding midrange performance of the Altec 414A woofer loaded inside the 614 bass reflex cabinet. In an ideal world, the blend should be seamless, with the horn/driver combo just filling in the missing upper frequency harmonic overtones not within the reach of the woofer.

Altec 802D
16 ohm original aluminum diaphragm
Alnico magnet

The 802D has been a musical companion for almost 20 years, so I know it very well. Attached to the 32C horn and playing duets with the 414A, they produce a harmonically rich and luscious midrange along with high frequencies that are silky smooth and extended. To my biased ears, it would be difficult to equal the 32C/802D/414A/614/JELN1600CXO quintet, short of a WE757A ;)

Emilar EC175-8
8 ohm original diaphragm
Ferrite magnet

My first impression of the EC175-8 which lingered all throughout my listening test, was a rich midrange reminiscent of the 802D. Perhaps this was due to its rather subtle presentation of high frequencies which are there, yet not stealing the limelight from the midrange. It's worth noting that this driver has a similar long throat design as the 802D. 

Renkus-Heinz SSD 1800-8
8 ohm original diaphragm
Ferrite magnet

The SSD 1800-8 + 414A was also a coherent combination. But the tonal balance was the antithesis of the EC175-8. The midrange sounded a bit leaner due to more prominent high frequencies. This driver has a short throat/pancake design like the 902-8B below. I wonder if the short throat configuration tends to enhance high frequencies?

Caveat: Based on my internet research, there are no original replacement diaphragms currently manufactured for Renkus-Heinz drivers.

Altec 902-8B
8 ohm original diaphragm
Ferrite magnet

To make things more interesting I borrowed a pair of Altec 902-8B cherished by my buddy Joel. The sound of this driver is similar to the 802D with the midrange not quite as lush but still vivid and involving. Since it had the best high frequency extension and transient response, the sound was invigorating. 

Top left: Beyma 8 AG/N 8" fullrange
Top right: Beyma SM115 15" woofer
Bottom left: Beyma CP380M
Bottom right: OB experiment ca. '09

In early 2009 I experimented with the CP380M + 32C coupled to the 15" Beyma SM115 woofer in an open baffle. I was actually quite impressed by the potential of this combination which was the reason I bought them.

Beyma CP380M
16 ohm polyester diaphragm
Ferrite magnet

However, in the context of this survey, the CP380M did not fare as well as the other drivers. Although the sound was quite pleasant with good high frequency extension, I was constantly aware of a transition between the 414A and the horn. Perhaps it was really voiced for a Beyma woofer?

Coda

The Emilar EC175-8 and Renkus-Heinz SSD 1800-8 have their virtues and omissions. If their virtues were combined, then we have a true Altec alternative. Yet despite their minor flaws, mounted on the Altec 32B horn, both easily coalesced with the Altec 414A woofer which corroborated their genetic heritage. If I didn't have the 802D, I could have easily lived with either the EC175-8 or SSD 1800-8 with a slight preference for the EC175-8 just because I'm a midrange hedonist;) 

With regards to the Altec 802D vs. Altec 902-8B, it boils down to a matter of taste as well as availability and affordability. As for the Beyma, when time permits, I will rehash the OB/SM115 + CP380M/horn experiment and post my findings;)

Happy listening!