Thursday, July 16, 2020

Headphones: AKG, Grado, Koss and Sennheiser

Sennheiser HD40 from Hifi Engine

Back in the 80s, I used a Sennheiser HD40 to monitor my rehearsals recorded on a cassette deck and as a courtesy to my roommates and neighbors during late night listening. I preferred the sound of the open-backed HD40 over the heavy, closed cups of the Koss Pro 4AAs at the listening library at school.

After I left the conservatory and entered the world of classical music performance, I also did a fair bit of recording gigs. This exposed me to various models from AKG, Beyer-Dynamic and Sennheiser. However, I never really paid attention to the subtle differences in headphones. I viewed them mainly as a temporary monitor, not as an alternative form of enjoying recorded music. 

When my HD40 died in the early 90s, I acquired a Grado SR80 as a quick replacement, since I was already a dedicated user of the GTE+1 and Signature 8 phono cartridges. 

Koss Porta Pro, Grado SR80 and AKG K72

A few years ago, I bought the closed back AKG K72 for my iPad so I wouldn't be bothering Tish when I got engrossed watching a movie or listening to music until the wee hours of the morning. BIG mistake! It's a totally different animal from the K240 I had positive memories of, from studio gigs in the past. The K72 sounds harsh and compressed. It can't even properly reproduce a human speaking voice.😬

After the Darling Amp, JE Labs style was uploaded, I got a steady stream of PMs asking if the amp could be configured as a headphone amplifier. This sparked my curiosity about headphones. Although I wasn't totally clueless, I didn't realize the vastness of the headphone audio sub-culture until Google turned up pages upon pages of headphone forums and blogs. 

Being a sucker for nostalgia, I ordered a pair of Koss Porta Pros from Amazon when I found out that they're still in production. The Porta Pros confirmed my long held suspicion that something was funky with the voicing of my SR80 headphones, which I also hear from my Grado phono cartridges. 

The Grado SR80 has been displaced 😔

Using this chart, it sounds like Grado Labs tailored an upper bass boost then created a dip starting in the lower midrange all throughout the midrange, followed by an upper
 midrange rise for the next two and a half octaves until response drops off sharply. This curve creates an impression of tonal warmth, heightened transparency and dynamic excitement. Although it is tame enough not to be outright objectionable and quite possibly appealing to others, it is fatiguing to my ears, especially under long term listening conditions. I gave up on my pair of Altec 811 horns for similar reasons. 

How could I have missed the Koss Porta Pro in the 80s? I'm so impressed with the Porta Pro that I also got the slightly cheaper KPH30iwhich supposedly uses the same drivers. Granted, the warmer voicing on both models is a personal preference, both headphones still have a much flatter response than the SR80. If forced to split hairs, the KPH30i is tonally the more neutral of the siblings. 

Koss Porta Pro and KPH30i with Yaxi Pads

Either one can be end game to music lovers who just want to enjoy their music on a tablet, cell phone or any portable device, because they're very efficient and an easy load to drive - no need for fancy headphone amps, just plug 'n play. The Yaxi pads take comfort to another level with the additional benefit of increased definition without negating their inherent virtues. 

It should be noted that the Porta Pro and KPH30i aren't for head bangers. The sound congests at louder levels, especially on complex musical passages. That's when the listener is reminded of its maximum SPL limit. I can live with that since I owned BBC LS3/5As and still use Altec 755Cs and 755As. It's a real world compromise I've learned to accept from coherent-sounding BUT small drivers that can't defy the laws of physics.

Nonetheless, for sheer musical pleasure, one can't go wrong with a pair of Porta Pros or the KPH30i. Add a pair of Yaxi Pads and the tab is still under 50 bucks, while the retro vibe is free! 😎 

Sennheiser HD420SL + AKG K240 Monitor

Since I love traveling back in time, I hunted for an HD40 but couldn't find a survivor. So I went a model up, only to find out that the HD414 has been rediscovered by the mainstream audio press and now commands Sotheby's prices. I finally settled on HD420SLs. After a bit of cleaning and new foam pads, it brought me back to the early 80s - lightweight, comfortable and sounds very much like the HD40 with a bit more extension at both frequency extremes. I'm hoping my memory still serves me right. Typical of headphones of its era, this needs an amp for best performance. While enjoying the trip back to the 80s, the HD420SL left me looking for a 'studio monitor' sound.

Undeterred by my AKG K72 experience, I located an older, Austrian-made, AKG K240 600 ohm monitor. My particular unit looked like a veteran of the studios. I had to get a new headband and rubber bands for it to fit properly on my head. Very inefficient, it barely croaked when plugged to my iPad. So I rigged a contraption to connect it directly to the output terminals of the Darling amp or Simple 46 amp

JEL Simple 46 + Noguchi FM-6WS OPTs
+ headphone adapter

This classic semi-open design delivers a neutral and transparent midrange, wide bandwidth, excellent micro-dynamics with fine resolution of detail, yet is fatigue-free. But I was left longing for warmth and air as found in great concert halls.

As Covid-19 lockdown loomed and gigs got cancelled, I needed a diversion. If cost wasn't a major factor, I would've ordered a Sennheiser HD600 from Amazon. But after reading many rave reviews of its sibling, the HD650, I opted for the [Mass]drop.com 'value for money' version, the Sennheiser HD6xx. It's more efficient than the K240/600M but it still plays its best amplified. 

Sennheiser HD6xx from Drop

Compared to the K240/600M, the HD6xx has better extension in the frequency extremes. I got the warmth and concert hall airiness I longed for + a more 3-D midrange. Micro and macro dynamic contrasts are vividly rendered, making the K240/600M sound comparatively less exciting. However, at higher SPLs, for example Mahler and Shostakovich orchestral climaxes, the distinction and layering of instruments sound strained and veiled. On the other hand, the K240/600M maintains its full composure and resolves these details with ease, albeit with less dynamic impact. Should I have gotten the HD600 instead?🤔

Wait, the doorbell's ringing... 

USPS just delivered this.


I've fallen into a rabbit hole. 😆





Thursday, July 2, 2020

Reality Check: Musical Instrument Frequency Chart + A Tidbit of Wisdom from Radiotron 3rd Edition


Musical Instrument Frequency Chart



This musical instrument frequency chart should serve as a reality check for those who obsess about metrics. During the triode era and up until cycles per second (cps) was replaced by kilohertz (kHz), a bandwidth specification of + or - 1dB from 30-15,000 cps was considered state of the art. That old standard actually made more sense if we look at the bandwidth of acoustic instruments in the chart above.

The chart is also a practical reference for all of my speaker/driver/horn articles past, present and future. Likewise, it is a handy visual aid to interpolate the pink noise + iPhone Real Time Analyzer (RTA) app traces even if in most cases they don't correlate to what we hear.😆  

In a couple of instances, an RTA trace has agreed with what I heard. In reality though, pink noise and other waveforms used for audio testing have nothing in common with musical notes and harmonies. Audio measurement is very far removed from the dynamic nature of music. To me, the RTA, audio generator and oscilloscope are tools that can be helpful if used with discretion.

Altec 755A in an Open Baffle



My adventure into high-efficiency speakers started with a pair of Altec 755Cs (and later, 755As) mounted on this very same open baffle. It was easy for me to appreciate the lack of boxy coloration, having lived with Quad ESLs for a couple of years.


Most open baffle detractors complain about the lack of bass response. However, the above trace doesn't pale too much in comparison to the Altec 755A + Dr. Bae/Silbatone box and Altec 755A + 618 below, even if it does look ugly!🤣

Maybe the suck out between 250-1kHz is what I hear as the absence of cabinet coloration or the "lack of snap" J-Rob heard?

Dr. Bae/Silbatone Box + Altec 755A



Despite being very compact, this empirically designed box exploits the fullest potential of the 755A driver. 


This trace looks better than the 755A + OB above but not as nice as the Altec 755A + 618 trace below.

Altec 755A + Altec 618

[2 cubic foot sealed box]


A pair of Altec 618 cabinets

The Altec 618 is the classic 2 cubic foot sealed box for the 755. It has to be rigidly braced to minimize upper bass/lower midrange coloration, although some listeners may prefer that "warm" bloom.

Altec 755A in the 618 box

This trace is the flattest of all three. But subjectively, the Dr. Bae/Silbatone box + 755A sounds more neutral and tonally more accurate. I don't hear the sudden rise from 1 kHz and peaks at 1.5 and 2 kHz. 

The Altec 618 box is now loaded with 755Cs and has great synergy with the JLH 1969 clone amp.

Altec 753C



 My exposure to the Western Electric WE757A and WE753C in the late 90s inspired the Altec 2-way project. The sound of those two classic speaker systems was already familiar. They sounded very similar to the 755A with more extension in the low end + airier highs. But what really sent me on a quest to emulate them were: greater efficiency so that I can enjoy my flea powered SE-DHT amps and less congestion (more layering and instrument separation) at higher SPLs. The Altec 753C is the final destination of that journey. 

Along the way, the Altec 755A was my loyal guide for midrange accuracy and coherence, which is why I discussed the driver in its various guises above.

Altec 414A in the ported 753C cabinet

The Altec 414A woofer running in full-range mode covers at least six octaves, from 45 Hz until it starts rolling off in the 3 kHz region. Unlike most drivers of this size and type, this is very smooth-sounding and delivers a great midrange without nasty cone break up modes up to its natural roll off point.

Prior to using the 414A, I had a pair of Altec 419A Bi-flex. I also seriously considered a pair of Altec 416A but both drivers exhibited nasty peaks starting from 1-3 kHz. Now I wonder if those peaks would've been visible using pink noise + my iPhone RTA app? 

I could've studied how to filter the peaks using EQ. However, all these extra crossover circuit complications would've adversely affected the efficiency of the speaker system, which I wanted to avoid. In the end, I stuck with my original plan of keeping it simple.

Altec 414A


Fundamental frequencies below 45 Hz may look rolled off in the trace but the harmonic overtone series (hence, harmonics or harmonic overtones) of the frequencies below the roll off point reinforce the [weak] fundamental in making those lower frequencies audible in actual musical reproduction. The BBC LS3/5A is a good example of a small speaker that "reproduces" low frequencies via harmonic overtones. 

My straightforward explanation: A:27.5 Hz played on an upright piano will produce less intensity as a fundamental note compared to that from a nine-foot concert grand because the instrument is physically smaller and the length of string, shorter. However, that upright piano's A:27.5 Hz is still perceived as A:27.5 Hz by the human ear, albeit less visceral, because of the harmonic overtones produced. 

Due to the 414A's sharp roll off past 3 kHz, the upper frequencies need reinforcement. 

Altec 32C horn + 802D + 20275 diaphragm
XO below

For many years, I struggled to make the Altec 811 horn work in this context. I started crossing it at around 900Hz @ 6dB/octave slope. Then, I cloned the Altec N1600C crossover, which effectively raised the crossover point an octave higher with a sharper 12dB/octave slope. 

None of these crossovers could blend the 414A and the 811/802D coherently to mimic my favorite full-range driver, the 755A. The "shouty distortion" was always present even with a simple 2 uf paper in oil cap + variable L-pad.

Altec 32C + 802D

After several years of frustration to the point I almost gave up, a fortuitous meeting with the Altec 32C horn opened a whole new world for the better.😄 It turned out that the objectionable "shout" I was hearing emanated from the Altec 811 horn.

The Altec 32C horn + 802D driver combo fill in the last 2 octaves of fundamentals + another 2 octaves of harmonic overtones using the high-pass crossover below. 

Sound Practices


I've learned so much from getting to know the Altec 755A, 755C414A, 802D and 32C intimately as well as from the other components that I ultimately rejected. 

The countless hours I spent assessing and listening to these transducers individually is a sound practice I highly recommend to audio DIYers!

Simple Crossover


Ever since I discovered the sonic delights of paper in oil as coupling capacitors in the signal path of preamp and amp circuits, I've also adapted their use in crossovers. 

Altec 753C crossover using paper in oil capacitors + Mills
non-inductive resistors
schematic

I've found the RTA to be helpful in adjusting crossover points with the help of a crossover calculator. A simple example: if the sound is harsh, move the crossover point higher. If you need more bite or presence, go lower.



Altec 414A + 32C horn + 802D compression driver  +
JP 753C ported cabinet = Altec 753C

If I were to summarize, the Altec 753C sounds lush and romantic!


Driven by 3500 milliwatts per channel of SE-DHT power, these speakers allow me to enjoy Mahler symphonies in my man cave with nuanced macro and micro dynamic contrasts. It gives a middle of the hall presentation which is my preferred perspective. The midrange is warm and coherent with a nice three dimensional quality.

Even if the extreme lows are curtailed, the harmonic overtones produced in this frequency region have enough foundation for big orchestral works. There's a wispy ribbon-like airiness in the extreme top which, to my ears, no longer need help from my pair of Altec 3000H super tweeters.

I probably could've gotten another half octave of bass extension if I chose the 15" Altec 416A woofer, but then I would've run into problems blending it with the 32C/802D horn/driver using a simple crossover. Even if I succeeded in EQ'ing out the peaks of the 416A, efficiency and midrange coherence would've suffered.

Everything is a compromise and I believe I've chosen wisely.

Wanted: smooth sounding 12"-15" wide range driver + horn + compression driver


Although Great Plains Audio is still manufacturing the 414 and 802 drivers with alnico magnets, IMHO, the listed prices are too steep to even attract the attention of the DIY community or smaller boutique manufacturers. 

I've used and highly recommend their replacement aluminum diaphragms for 1" format compression drivers. I've been told that the GPA 414 doesn't sound like the classic 414A/Z/8B/16B and is 3dB less efficient. However, I don't have hands-on experience with the GPA drivers to confirm any of those claims.

GPA is our only direct connection to the past when transducers were designed using human ears aided by measurement tools. For that alone, I want them to succeed!

Radiotron, 3rd Edition Redux



Let's (re)visit a topic that has served the interest of the entire audio industry, except the bottom-line of this hobby - the enjoyment of music!


Sad to say, no one has heeded D. Massa's advice. 

Besides, the test tones used for distortion analysis have no bearing whatsoever to the highly dynamic and complex harmonies contained in the simplest musical score.


Yup, this was 80 some years ago and there still are self-proclaimed audio pontiffs who insist on this metric!🙄




Wednesday, June 17, 2020

Moving Magnet Cartridges from Audio Technica, Pickering/Stanton and Shure



This installment will cover successors to moving magnet phono cartridges I discussed a couple of months ago. The cartridges were evaluated in the near-field system and cross-referenced with the main system. Tonearms used include the Fidelity Research FR54, FR24 MKII, Grace G565 and SME 3012, mounted on the following turntables: Garrard 401, Thorens TD124 Mk I or II, Rek O Kut B12GH or Shield MO-19.

Top to bottom: Audio-Technica AT3600L, AT110E and AT3600L+Pfanstiehl stylus   

Audio-Technica

Audio-Technica AT3600L
Vertical Tracking Force (VTF) Range = 3-5 grams
Tested @ 3g VTF

This $10-15 Audio Technica cartridge gained notoriety when it became known as the OEM version of the Rega Carbon. It has a pleasant sound, which highlights the midrange due to truncated frequency extremes. 

After prolonged listening, I noted compressed dynamics and slightly grainy (but pleasant) upper end. For the price, this is a musically balanced cartridge with colorations that enhance rather than detract from the musical experience.

AT3600 body + $10 Pfanstiehl conical stylus
Tested @ 2.5g VTF

As a $10 experiment, I ordered a generic Pfanstiehl conical stylus with aluminum cantilever. This stylus looks very similar to the one fitted to the Audio-Technica CN5625AL sans A-T logo. 

The aluminum cantilevered conical stylus took away most of the graininess, giving a more harmonious sound, while simultaneously improving the frequency extremes and detail resolution. In spite of the improvements, the sound was still "closed-in." 

Audio-Technica AT110E
Tested @ 2g VTF

The AT110E was an 80s entry-level model highly regarded by the UK audio press. I've kept it all these years as a back-up and threw it in the mix for perspective.

No contest! The sound opened up and everything came into focus from the midrange and both ways to the frequency extremes with much greater resolution.


Top: Pickering V-15+DAT2
Bottom: Stanton 500V3

Pickering V15/Stanton 500V3 

Pickering V15 body + DAT2 Conical Stylus
Tested @ 3.5g VTF

The Pickering V15 + DAT2 has a very sweet and 3-D midrange! Its tonal character is very reminiscent of its moving iron ancestor, the Pickering 380. High frequency performance is not quite as extended as the SC39B/ED or AT110E but it is silky smooth with life-like harmonic overtones. 

Bass extension is less, compared to the AT110E and SC39B/ED, but still at par with the M44 + EMJ N44G. Dynamics at micro and macro levels is better than the SC39B/ED and AT110E but not quite in the same league as the M44 + EMJ N44G. 

Stanton 500V3
Tested @ 3.5g VTF

I thought the 500V3 sounded very similar to the Stanton 500 Mk II when I compared them in the early 2000sBut I was disappointed with this sample I acquired in 2016. In spite of the slightly better bass impact vis a vis the V-15+DAT2, the 500V3 sounded peaky in the upper midrange (most noticeable on female vocals), with a sizzling top end compared to its older stable mate.

Swapping the DAT2 stylus in the 500V3 body tamed a bit of the harshness but the midrange still wasn't as liquid. Quality control may have declined at the tail end of Pickering/Stanton production. In fairness though, I'd rather listen to this cartridge than the AT3600L.

Left to Right: Shure SC35C, M44-7 + Pfanstiehl, M44 + EMJ N44G, SC39B
and SC39ED stylus (right front) 


Shure


Late 90s Shure SC35C
Tested @ 3.5g VTF

Twenty years ago, I found the SC35C to be a good alternative to the M3D and M7D, albeit with a modern tonal character. But after being exposed to other Shure models in this survey, the SC35C sounded comparatively dry, grainy and the least transparent.

Its neutral tonal balance is its greatest asset! However, the high VTF requirement of 3.5 - 5 grams might scare the younger generation of audiophiles.
Shure M44 body + Pfanstiehl 0.7 mil spherical stylus
Tested @ 4g VTF 

The Shure 44-7 + generic (Pfanstiehl) 0.7 mil spherical stylus is a very dynamic and exciting combination. Shure admits boosting the bass frequencies - I hear boosted mid > upper bass + sibilants in vocals due to a rising upper midrange to lower highs.

The listening experience brought me back to the 80s NYC club scene of Palladium and Nel's. Great for spinning 12" 33/45 rpm singles to relive 80s club days. BUT NOT for serious listening to vocals, jazz or classical. Very HIGH output, close to 10mV and it also requires high VTF in the range of 3-4g. 

M44-7 body + EMJ N44G stylus
Tested @ 3g VTF

Since genuine N44G styli are hard to find and if ever available, demand exorbitant amounts, I took a chance on this EMJ N44G stylus for my other M44-7 body because of the EMJ website description, "It's NOT for DJ play but for ordinary listening."

This Japanese 0.6 mil conical stylus mounted on an M44 body is a highly refined performer. It retains the exciting dynamics of the M44-7 + generic stylus above, while all the rough edges are polished. It may not have the dignity of the M3D or M7D, but it preserves most of their virtues including the 3D midrange. It is a worthy descendant with better tracking ability. Definitely not an ordinary listening experience! 😁

Shure SC39ED
Tested @ 1.5g VTF

It would have been nice if I had access to a Shure V-15 Type IV or V but the SC39ED is as close as I could get to a top of the line Shure cartridge. The light tracking force range of 1.25 - 1.5 grams will be most welcomed by those afflicted with over 2 grams VTF phobia.

Mounted on the FR54 or Grace G565, this cartridge sounded tired and soggy. But it woke up once mounted in my lowest mass tonearm with interchangeable head shell - the Fidelity Research FR24 MkII.

This cartridge exemplifies the sound of flat frequency response and high detail resolution. The tonal balance is very neutral like the SC35C but with less grain and greater transparency. It also has the most extended frequency response at both ends of the spectrum in this survey.

With all that detail and such wide frequency response, I wonder where the passion and soul of the music went?

SC39B
Tested @ 2g VTF

I was about to give up on the SC39ED's lack of musicality when I spotted an original SS39B spherical stylus for this cartridge body at V-M. The simpler stylus profile brought a much needed joi de vivre to this cartridge body and I started enjoying music again! 

CODA


After a head to head comparison with its older sibling, the AT110E, my enthusiasm for the Audio-Technica AT3600L was dampened. For sheer musical pleasure, it's obvious that my personal picks are the Pickering V-15/DAT-2 and the Shure M44 body + EMJ N44G!

Even if the Audio-Technica AT110E, Shure SC35C and SC39B/ED don't meet my musical requirements, their virtues should fulfill mainstream audiophile expectations. So don't let my bias stop you from pursuing them. Listen and decide for yourself.

All these cartridges are no longer in production except for the AT3600L. But since they were massed produced from the 60s to the 90s, they're not difficult to find and replacement styli are readily available. 

There are more classic cartridges out there to try and I hope this article encourages other audio hobbyists to embark on their own journey.